4-Axis DIY Drone PIX PX4 Flight Controller 560mm Carbon Fiber Foldable Frame 700KV Brushless Motor 40A ESC 1455 Props AT9S Radio

    3 Options , pls check carefully before place the order  . 

    PNP NO RX 

    Carbon fiber folding frame kit x1(Unassembled）

    HYD3508 700kv brushless motor x4(banana plug Soldered )

    1455 carbon fiber propeller x2

    Reverse buckle tie x1

    Non-folding Landing gear x1

    Antenna Holder x1

    Servo cable x1

    GPS X1

    PIX PX4 Flight Controller Set x1

    BNF With RX

    Carbon fiber folding frame kit x1(Unassembled）

    HYD3508 700kv brushless motor x4(banana plug Soldered)

    1455 carbon fiber propeller x2

    Reverse buckle tie x1

    Non-folding Landing gear x1

    Antenna Holder x1

    Servo cable x1

    GPS X1

    PIX PX4 Flight Controller Set x1

    T8FB Transmiter with R8EF Receiver  

    RTF With Battery

    Carbon fiber folding frame kit x1(Unassembled）

    HYD3508 700kv brushless motor x4(banana plug Soldered )

    1455 carbon fiber propeller x2

    Reverse buckle tie x1

    Non-folding Landing gear x1

    Antenna Holder x1

    Servo cable x1

    GPS X1

    PIX PX4 Flight Controller Set x1

    T8FB Transmiter with R8EF Receiver  x1

    11.1V 4400MAH 30C 3S1P xt60 x1 

    Charger x1

    More Details:

    Frame kit: 

         Wheelbase: 560mm

     Fit for Motor:2212-3508(920kv - 700kv)

     Fit for ESC: 20A-40A

     Height of the Landing Skid: 190mm

     Fit for Propeller: 10-12 inch

    Propeller: 

    High quality 100% 3K all carbon fiber board which imported from Japan improve material.

    Each pair of propellers has perfect dynamic poise and static balancing which balance by manpower.

    Especially improves the air-powered efficiency and aerofoil stability.

    High quality ultra-light carbon fiber propellers especially designed for multicopters.

    Carbon fiber forward propeller*1

    Carbon fiber reverse propeller*1

    Length:14inch,Pitch 5.5,Main Hole Dia 4mm,Side Holes Dia 3mm,Center distance 12mm

    Motor:

    Motor KV: 700KV

    Shaft: 4.0mm

    No-load Currency (A): 0.4A

    Maximum Currency (A): 18.0A

    Power: 198W

    Weight: about 90g

    Input Voltage: 2-4S LOPO

    Suitable Propeller: 12"-15" Props

    ESC:

    Types: long, short

Current:  40A

Output capacity: continuous current 40A, short-time current 55A (not less than 10 seconds)

Power input: 2-4 lithium batteries(Not Included)

BEC output: 5V@3A (linear regulator mode - linear mode)

Maximum speed: 210,000 rpm for 2-pole motor, 7000 rpm for 6-pole motor, 35,000 rpm for 12-pole motor

Size: (Approx) 68x25x8mm

    B3 pro Charger :

    Input Voltage : 100 - 240V AC50 / 60Hz

         Output Current: 3*800mA    

         Suitable for 2 cell and 3 cell Li-Po Batteries    

         Led Indicator:    

         When power is on : Orange    

         Stand by mode : Green    

         Battery Charging : Red    

    Battery Full : Green

    T8FB Technical Parameters

    1. Size: T8FB - 173*102*206mm, R8EH - 48.5*21*11mm.

2.Weight: 0.47kg(including R8EH)

3.Frequency: 2.4GHz ISM band(2400MHz~2483.5MHz)

4.Modulation mode: GFSK

5.Channel bandwidth: 400KHz

6.Band width:1200KHz

7.Spread spectrum: FHSS

8.Adjacent channel rejection: >36dBM

9.Transmitter power: <100mW (20dBM)

10.Sensitivity: -104dBM

11.Speed rate:38kbps

12.PWM output: 1.0ms~2.0ms

13.Section precision: 2000, 0.5us per section

14.Cycle:15 ms/per frame

15.Radio T8FB operating voltage: 4.8V~18V

16.Radio T8FB operating current: <110mA

17.Receiver R8EF operating voltage: 4.6~10V

18.Receiver R8EF operating current: <30mA

19.Control distance: more than 1000 meters air, the actual control distance depends on the flying environment.

    R8EH Receiver: 

Channel: 8CH

Operating voltage: max 10V.

Operating current: 19-25mA(input voltage 5V)

Size: 48.5*21*11mm

Weight: 7g

Section precision: 4096

Signal output: S-BUS, PPM and PWM PWM

signal mode: Green LED, output 8 channel PWM signal.

SBUS/PPM signal mode: Both red and green LED on, CH1 output S-BUS signal, CH2 output PPM signal, CH3 to CH8 output PWM signal at the same time.